The Manual C8 Corvette Is Finally Real. Here’s How a Hard-Working Tuner Shop Did It
The Drive ·

Alex Peitz of Peitz Performance Tunes explains how he developed the C8 manual conversion, when you can expect to be able to buy one, and approximately how much it will cost. The post The Manual C8 Corvette Is Finally Real. Here’s How a Hard-Working Tuner Shop Did It appeared first on The Drive .
I’m suddenly more than a little jealous of my colleague Byron Hurd —he’s now one of the only people on planet Earth to have driven a C8 Corvette with a manual transmission . The trans itself is a Tremec unit, but it was a tuner shop in Texas called Peitz Performance Tunes that actually cracked the code to make it functional. I caught up with Alex Peitz, the owner and tuner there, to find out how he worked his magic and when consumers will be able to buy their own C8 manual conversion kits.
First, I asked him what the car’s like to drive. And even though we have Hurd’s impressions (linked above), Peitz has a lot more miles on it, including highway blasts and running full noise on track.
“Like I tell everybody, it’s a transformative experience. It’s impossible to drive this car and not have a smile on your face. Actually, the president of Shelby American drove it on Sunday. He had a sneak peek into it and he was doing donuts in the parking lot of Shelby, and he loved it. I mean, you can just see his reaction.”
“It’s just a completely different, it’s a visceral, raw driving experience. And some people say, ‘oh, it’s going to be slower.’ Well, I mean, define ‘slower.’ In what aspects? But at the same time, if you feel the acceleration rate that this thing has, it starts to make you question if the DCT is necessarily going to be faster in some rides. Of course, the shift speed is potentially going to be faster with DCT because obviously it’s a computer controlling it, right? However, we have upshift ignition cuts where you have no lift shift and downshift flips.”
“[For a control unit] we have the M150. The MoTeC M150 is managing the inputs from the transmission. So we can see gear position, we can see speeds, we can see, obviously, clutch position. So the M182, which manages the engine, knows when all these things are happening. And so it can do the upshift cuts, the downshift clips, and make all of those things work appropriately. So, yeah, it just makes for an awesome driving experience. You don’t have to use that stuff. Of course I heel-toe it, and that’s fun too. But yeah, I mean, it’s an absolute riot.”
“… Tremec announced this transmission, the TR 9060, last year at SEMA,” Peitz reminded me. “And then they’re obviously going through finalization of that. But they designed it because they used the C8 mounting points already. So that made that portion of it very easy, obviously. And yeah, it was about a four-degree difference as far as where the flanges landed for the half shafts, but that was fine, within the margin of where it could be. So that wasn’t a problem.”
“So that was all seamless just because it was already designed around the C8 mounting points. Biggest thing is the shifter, the clutch pedal, all those two things were the biggest beasts mechanically speaking. Electronically speaking, obviously, the MoTeC plug-and-play package we’ve been working on for over four years now. I can’t tell you the countless amount of money and hours I have in that thing. But the shifter started off life as a Porsche shifter, an aftermarket shifter that a company offers.”
“I can’t remember the name of the company right now off the top of my head, but 20% of that thing is left. Now we’ve completely modified it, adjusted the pivot points and things of that nature to make it work how it does. We’re going to go back and make a production-friendly version, machine our own shifter from scratch, essentially.”
“And then the clutch pedal started off as a CT4V Blackwing pedal, which barely any of that is remaining as well, maybe 10% of that. But we did use the master cylinder from it, and then we ran new hydraulics, of course.”
“We also had some dry fittings in there. So in case we disconnect the line, we still retain the … You don’t have to bleed it again, basically. So just things of that nature we did as well. Other than that, the mechanicals of it and getting it installed, we spent, granted, most of our shop was working on it for two weeks because we didn’t have but maybe two, two and a half, three weeks at tops to get all this done before we had to get it here to SEMA because we got the gearbox later than what we would’ve wanted, but it all worked out.”
“So the transmissions themselves are going to be in production and be available around July of next year,” Peitz explained. “And then our installation package, if you will, we’ll have that done before then. So we’re actually accepting pre-orders, but the price all-in when you’re done with it right now with the MoTeC plug and play, all the hardware and software and firmware involved with that, plus the CAN bridge that comes with the patch harnesses, the PCB conversion boards, you’re still using the factory harness. All of that, and then it’s about $75,000 all in.”
You’ll have to provide a C8 on top of that, too. So this is not going to be a mass-appeal product. Just a special experience for the select few who positively must have a three-pedal mid-engine Corvette.
“Yeah, so, I bought this car back in 2020 to make it a race car,” Peitz told me. “And so I actually wrecked it at NCM in October of 2020 at a race. And so at that point, that kind of started the process, kicked me into gear a little bit. So the car sat because I pulled the transmission out, pulled the engine out. I was going to do a flat plane crank conversion on this, but I ended up doing a flat plane conversion on an LT2, but because I was going to end up racing this in the DLGT class for Gridlife, I sold that flat plane LT2 to another customer. So that’s another project. We’ve already got it running, actually. It’s cool. You can check that out as well. But with this case, yeah, I knew I was going to make it a race car. I’d already wrecked it.”
“I’m like, ‘all right, let’s make it a race car.’ But it sat as a shell for probably three, four years. We did the cage; we did a bunch of the chassis stuff. I’d done the coilovers, but I hadn’t determined what engine setup I was going to do because at that time the GLGT class didn’t exist. And so when I heard that was coming out in ’25, it was like mid to late ’24. I’m like, ‘all right, I’m just going to do mostly stock engine with our heads cam and then put it back because I don’t need to add a bunch of extra engine mods because I’m going to be detuning it for the class anyways.’ So, yeah, as far as the transmission itself, I bought this car also to develop various products, and we’ve been developing the MoTeC plug-and-play on this for this whole time.
“And then I’ve been working with Tremec as far as coming here to the booth [at SEMA], displaying different cars for the last couple of years. And when they announced that transmission last year, obviously we were talking, and they knew I had been doing the MoTeC plug-and-play. It’s like, ‘Hey, do you want to put a manual transmission in your C8?’ And it didn’t take me but negative three seconds to say ‘yes.’ So yeah, they sent me the CAD model. I already have the car in CAD, so we’re able to mock up a lot of stuff and kind of just see how things are going to lay out, figure out the shift cables and those lengths and all that went into it.”
We’ll be keeping tabs on this project for sure. Here’s hoping these conversions start proliferating sooner rather than later!
Got a story tip? Or better yet, a radical build like this in your barn? Drop us a line at tips@thedrive.com.
The post The Manual C8 Corvette Is Finally Real. Here’s How a Hard-Working Tuner Shop Did It appeared first on The Drive .